首页
点击图片查看原图
东莞市景舜复合材料有限公司旗下四大品牌：“巨箭JUKAM、全能王QNVOR、胶匠JOJON、KEYDAK”，所有产品均通过欧美环保认证，应用材质涵盖：工程塑料,ABS,不饱和聚酯,聚乙烯,聚丙烯,硅橡胶,EPDM,压克力,橡胶(天然橡胶、丁基橡胶),玻璃（普通玻璃、钢化玻璃），陶瓷,纤维(碳纤维、尼龙),纸,金属(不锈钢,铁,铜,铝),聚苯乙烯,聚氯乙烯,聚碳酸酯,聚胺酯(PU),木制品,工艺品,玩具等；销售网络覆盖全球,凭着其优良的质量享誉世界。
东莞市景舜复合材料有限公司年生产能力高达5000吨,具备有精良的专业研发设备配合生产研究,以保证产品的不断改良优化及新产品的不断推出,紧随社会发展步伐,走在行业的前端。为更好的服务于市场，增强企业覆盖广度，于2001年引进最新的紫外线胶粘剂生产技术，生产“KEYDAK”品牌紫外线胶系列产品。公司凭借ISO及5S的精神，秉承 “ 诚信 、 进取、 创新 、 严谨 ”的企业文化，坚持“ 客户至上 、 永恒发展 ”的经营理念，使企业得以持续有效的发展！
景舜优势:1.品质一流 2.技术先进 3.设备齐全 4.人才积淀
Contact person：134 1666 5501
巨箭G-257亚克力胶水产品简述
巨箭JUKAM G-257 亚克力PMMA专用接着剂综合了溶剂型与树脂型粘接剂的优点、
摒弃了其各自的缺点，从而实现了其粘接速度快（数秒内可定位）、强度大、无气泡、不发白、不发黄、不发裂、透明度理想的粘接效果。
G-257 Acrylic Glue Product Brief
Jujiao JUKAM G-257 Acrylic PMMA special agent combines the advantages of solvent type and resin type adhesive,To abandon their own shortcomings, so as to achieve its fast bonding (within a few seconds can be positioned), strength, no bubbles, no white, not yellow, not cracking, transparency ideal bonding effect.
本品完全固化可达本体强度的98%以上；
本品可取代UV紫外线胶，不需要紫外线灯光照射，借助太阳光或自然光即可瞬间固化，可为工
厂节省大量的生产成本；
本品适用范围广泛，可用于各种压克力板材粘接、挤出及浇铸压克力制品的粘接，对进口板材效
果，可实现立面、平面、斜面粘接等
This product is fully cured up to 98% of the body strength;
This product can replace UV UV glue, do not need ultraviolet light irradiation, with the help of sunlight or natural light can instantly solidify, for the workers
Plant to save a lot of production costs;
This product is suitable for a wide range of acrylic sheet can be used for bonding, extrusion and casting acrylic products bonding, the import plate effect
Fruit, can be achieved facade, plane, slope and so on
巨箭G-257亚克力胶水操作要领
对接
将两块需对接的压克力板水平放置操作平台上，合拢，并在底部粘一胶带，留下一条不大于0.3mm
宽的缝隙以备涂沆粘接剂。
用注射器将本粘接剂从一边均匀缓慢从缝隙里注入，直到全部注满，待完全固化后揭去胶带即可。
Docking
The two need to dock the acrylic plate placed on the operating platform, close together, and in the bottom of a tape, leaving a not more than 0.3mm
Wide gap to prepare for the paste.
With the syringe to the adhesive from one side slowly and slowly from the gap into the until all filled, to be completely cured after the tape can be removed.
立面粘接
立面粘接是应用广泛的一种粘接技术，在制作各种压克力制品中得到普遍的使用。
首先应将需粘接的表面擦拭干净。
使用靠模实现粘接，使粘接物不晃动，有利于提高粘接的质量。
厚度为3mm以内的压克力板粘接可直接用注射器从一边均匀而缓慢的注入本胶水，即可完成粘接。
厚度大于3mm的压克力板粘接，可垫入细金属丝，利用毛细作用完成粘接，在粘接剂固化前抽出
金属丝，或可采用把不须粘到的部位贴上胶带保护，留下涂粘接剂部位涂上粘接剂，再斜放入
压克力板挤出qi泡即可。
Facade bonding
Facade bonding is a widely used bonding technology, in the production of a variety of acrylic products are widely used.
First, the surface to be bonded should be wiped clean.
Use the mold to achieve the bonding, so that the adhesive does not shake, help to improve the quality of bonding.
The thickness of 3mm or less of the acrylic plate can be directly connected with a syringe from the side of the uniform and slow injection of the glue, you can complete the bonding.
Thickness greater than 3mm acrylic plate bonding, can be pad into the fine wire, the use of capillary action to complete the bonding, before curing the adhesive
Wire, or can be used to not stick to the site of the tape to protect the tape, leaving the adhesive coated parts coated with adhesive, and then inclined into the
Acrylic plate squeeze qi bubble can be.
斜面粘接
粘接斜面必须90度角靠模，才能防止被粘面的移位。
涂注本粘接剂时应均匀、缓慢。
待完全固化后才能取下靠模。
Beveled
Adhesive slope must be 90 degrees angle by the mold, in order to prevent the displacement of the sticky face.
This adhesive should be uniform and slow.
To be completely cured before they can be removed by the mold.
平面粘接
平面粘接是一种比较特殊的方法。
首先将被粘面擦拭干净，并水平置放，在上面注上适量本产品。
将另一块压克力板的一边斜放接触被涂了粘接剂的压克力上，然后均匀缓慢放下，从一边将气泡挤出而完成粘接。
Flat adhesion
Flat bonding is a rather special method.
First will be wiped by the sticky surface, and the level of placement, in the above note the amount of the product.
The other side of the acrylic plate side of the adhesive was coated with adhesive on the acrylic, and then evenly slowly put down from the side of the bubble out to complete the bonding.
